- 31–60 A output — cuts 5/8 in clean, 7/8 in severance. The Tomahawk 625 is Lincoln Electric's mid-range professional plasma cutter, built around the LC65 torch system and a 60 A inverter output. It handles the full range of structural fabrication tasks: cutting 1/4 in plate clean for welded frames, severing 3/4 in chain and threaded rod quickly, and processing 1/2 in grating with consistent kerf quality and low dross. Factory demo pricing delivers this capability at 15–25% below MAP.
- PowerConnect input — 230 V single-phase, easy panel connection. The Tomahawk 625 runs on 230 V single-phase input, the most common industrial and residential heavy-power configuration. No three-phase panel required, no special transformer — the same outlet used for a MIG welder or table saw feeds the 625. Input current at rated output is 37 A at 230 V, fitting a standard 40–50 A double-pole breaker.
- LC65 torch system — one of Lincoln's most widely supported plasma torch platforms. The Tomahawk 625 uses the LC65 consumable system: readily available at WeldingMart in electrode, nozzle, shield, retaining cap, and drag spacer configurations for both handheld and machine-torch cutting. Consumable interchangeability across Lincoln's mid-range plasma line means maintenance supplies are stocked and shipped within the same consumable order as the 375 Air or 1000.
- Factory demo with 20 ft hand torch included. This U2807-1 unit ships with the full-length LC65 20 ft handheld torch — the same torch sold separately as K2848-1. The 20 ft torch length provides working radius without moving the power source, useful for cutting flat tables and large sheets without repositioning the machine.
- Touch Start and rapid arc restrike for continuous cut performance. Touch Start eliminates high-frequency arc ignition and extends consumable life. Rapid arc restrike automatically re-ignites the plasma arc within milliseconds if the torch tip loses contact during a cut — critical for maintaining a continuous kerf through material surface irregularities without restarting the cutting sequence.
| SKU / Model | U2807-1 (Factory Reconditioned) |
| Clean Severance Cut | 5/8 in (15.9 mm) mild steel |
| Maximum Severance Cut | 7/8 in (22.2 mm) mild steel |
| Output Current Range | 12–60 A (continuously variable) |
| Rated Output | 60 A @ 96 VDC |
| Duty Cycle | 60% @ 60 A; 100% @ 45 A |
| Input Voltage | 230 V AC, 1-Phase, 50/60 Hz |
| Input Current (rated) | 37 A @ 230 V |
| Air Supply | External compressed air required (60–85 PSI, 4.0–6.0 CFM) |
| Arc Initiation | Touch Start — rapid arc restrike |
| Torch Included | LC65 Handheld Plasma Torch, 20 ft (6 m) — K2848-1 |
| Net Weight | 20 lbs (9.1 kg) |
| Dimensions (H×W×D) | 10.3 in × 6.6 in × 18.8 in (262 × 168 × 478 mm) |
| Warranty | 3 Years — full Lincoln Electric factory warranty |
| Condition | Factory Reconditioned — Lincoln Electric certified |
- Tomahawk 625 Power Source
- LC65 Handheld Plasma Torch, 20 ft (6 m) with cable assembly
- Work cable and clamp
- Power cord with 230 V plug
- Consumable kit (electrode, nozzle, shield cup, retaining cap, drag spacer)
- Operator's manual and factory warranty card
The Tomahawk 625's LC65 torch system and 60 A output support a full range of accessories available from WeldingMart:
- Replacement Plasma Torches — LC65 handheld torch 25 ft (K2848-1), LC65 machine torch 25 ft (K2848-3), and LC65 50 ft extended-reach torch (K2848-2) for automated cutting tables and long-reach applications
- Plasma Consumables — Tomahawk LC65 electrodes (KP2844-1), nozzles in 40 A, 50 A, and 60 A ratings, gouging nozzle (KP2844-8), shield cap assemblies (KP2844-13), and retaining caps (KP2844-10) — full LC65 consumable line stocked at WeldingMart
- Plasma Cutter Air Compressors — the Tomahawk 625 requires external compressed air at 60–85 PSI and 4.0–6.0 CFM; compatible portable compressors from WeldingMart supply the required flow for continuous 60 A cutting
- Tomahawk Circle-Cutting Guide K2886-1 — Lincoln's Tomahawk circle-cutting guide mounts to the LC65 torch drag shield for repeatable, radius-controlled cuts on pipe, flanges, and circular plate sections
The Tomahawk 625's 60 A output and 5/8 in clean-cut capacity position it as the right tool for structural fabrication shops, automotive fabricators, and field contractors cutting up to 3/4 in plate:
- Structural steel fabrication. Cutting gusset plates, saddle cuts on pipe ends, and tab-and-slot panels from 1/4 in to 1/2 in A36 plate is the Tomahawk 625's primary production environment. The LC65 torch's 20 ft lead reaches across a 4×8 ft cutting table without repositioning the power source; variable output tuning reduces dross on edge cuts that go directly to fit-up without grinding. Typical duty-cycle demand in production cutting is well under the 625's 60% rating at full 60 A output.
- Automotive fabrication and race car construction. Roll cage notch cuts, floor pan sections, firewall panels, and 4130 chromoly tubing end-preps demand clean plasma cuts with minimal heat-affected zone. The 625 cuts 3/16 in steel at full speed with a narrow, consistent kerf — floor pan replacements and door skins come off clean without grinder distortion of the adjacent metal.
- HVAC commercial ductwork. Heavy-gauge commercial HVAC duct (14–10 gauge) and structural duct hangers cut faster with the 625's 60 A output than with the smaller 375 Air's 27 A limit. The 20 ft torch lead and rapid arc restrike support continuous production cuts around duct perimeters on large-format fabrication tables.
- Industrial maintenance and millwright work. Cutting through rusted anchor bolts, seized structural members, and worn-out conveyor frames requires a robust plasma cutter that maintains consistent arc through mill scale, surface rust, and galvanized coatings. The 625's 60 A output and rapid arc restrike handle contaminated material surfaces where lower-powered plasma units lose arc stability.
- Art fabrication and decorative metal work. Plasma-cut decorative panels, weathervanes, architectural screens, and sculptural forms in mild steel, stainless, and aluminum benefit from the 625's wide output range (12–60 A). Fine detail cuts on thin material run at reduced amperages; heavy plate sections for base structures cut at full power — all from the same machine without consumable changes.
The Tomahawk 625 requires external compressed air at 60–85 PSI and 4.0–6.0 CFM at the torch. Unlike the Tomahawk 375 Air, the 625 does not include an internal compressor. A standard 20-gallon shop compressor running a 1.5–2 HP motor at full tank can supply the 625 adequately for intermittent cutting. Continuous production cutting at full output requires a compressor rated at 6+ CFM at 90 PSI to maintain consistent air pressure without recovery-cycle interruptions.
Lincoln Electric's factory reconditioned program returns used demo and evaluation units to factory-spec condition at Lincoln's certified service center. The unit is disassembled, inspected, cleaned, worn consumables replaced, tested to original output specifications, and repackaged with a full 3-year factory warranty. The U-prefix denotes Lincoln's "used/reconditioned" classification — not a field-used, trade-in, or non-Lincoln-serviced unit.
The Tomahawk 625 outputs up to 60 A and cuts 5/8 in clean / 7/8 in maximum on mild steel. The Tomahawk 1000 outputs up to 80 A and cuts 1 in clean / 1-1/4 in maximum. Both run on 230 V single-phase input. For structural fabrication of up to 1/2 in plate, the 625 handles most workloads. For regular production cutting of 3/4 in and thicker plate, or for heavier-duty severance work, the 1000 provides the additional amperage reserve.
Rapid arc restrike automatically re-initiates the plasma arc if it extinguishes mid-cut — for example, when the torch encounters a gap, a hole, or surface irregularity in the workpiece. Without restrike, the operator must release the trigger, reposition, and restart the arc manually. With restrike, the arc resumes within milliseconds, maintaining kerf continuity and preventing incomplete cuts in production environments.
Yes. WeldingMart stocks the complete LC65 consumable line: electrode (KP2844-1), nozzles in 40 A, 50 A, and 60 A ratings, shield assemblies (KP2844-13), retaining caps (KP2844-10), gouging nozzles (KP2844-8), and drag shields. Individual pieces and multi-pack kits ship within 1–3 business days.
Looking for the brand-new version? See the brand-new Tomahawk 625 with 20 ft Hand Torch or browse all plasma cutters and our full demo plasma cutter collection.
The Lincoln Tomahawk 625 Factory Reconditioned Plasma Cutter delivers professional 60 A plasma cutting capability at factory reconditioned pricing. This inverter-based plasma cutting system uses Lincoln Electric's LC65 torch platform, Touch Start arc initiation, and continuous variable output control to produce clean, precise cuts in mild steel, stainless steel, and aluminum up to 5/8 in thick — with severance capacity to 7/8 in for demolition and emergency cutting applications.
The Tomahawk 625 bridges the gap between compact plasma cutters and full-sized production units. At 20 lbs, it remains portable enough for field service and job site use while delivering the 60 A output needed for genuine structural fabrication: cutting 1/4 in A36 plate for welded frames, severing 1/2 in plate for machine bases, and processing structural angles and channels at production speed. Its 230 V single-phase input connects to any standard 50 A double-pole breaker without special wiring.
This U2807-1 unit has been factory reconditioned at Lincoln Electric's certified service center — disassembled, tested, serviced to original specifications, and repackaged with a full 3-year Lincoln Electric factory warranty. Factory reconditioned pricing is typically 15–25% below the MAP price of a new K2807-1 unit with identical specifications, identical warranty, and identical LC65 torch system.
The included 20 ft LC65 handheld torch provides full working radius around a 4×8 ft cutting table without repositioning the power source. The complete LC65 consumable line — electrodes, nozzles in three amperages, shields, retaining caps, and gouging nozzles — is stocked at WeldingMart and ships same-day.
- 60 A continuous output — cuts 5/8 in mild steel clean, 7/8 in severance
- 230 V, 1-Phase input — standard industrial and residential heavy-power circuit
- Touch Start arc initiation with rapid arc restrike — extended consumable life
- Continuously variable output control (12–60 A) for precise cut quality
- LC65 torch platform — full consumable line stocked at WeldingMart
- Includes 20 ft LC65 handheld torch (K2848-1) — 20 ft working radius from power source
- Compact design: 20 lbs; portable for field and job site use
- 60% duty cycle at 60 A — production-capable for continuous structural cutting
- Full 3-year Lincoln Electric factory warranty
| Input Voltage | 230 V AC, 1-Phase |
| Input Current (rated) | 37 A @ 230 V |
| Input Hertz | 50/60 Hz |
| Output Current Range | 12–60 A |
| Rated Output | 60 A @ 96 VDC |
| Duty Cycle | 60% @ 60 A; 100% @ 45 A |
| Clean Cut Capacity | 5/8 in (15.9 mm) mild steel |
| Severance Capacity | 7/8 in (22.2 mm) mild steel |
| Air Supply Required | 60–85 PSI, 4.0–6.0 CFM (external) |
| Arc Initiation | Touch Start + rapid arc restrike |
| Torch | LC65 Handheld, 20 ft (6 m) — K2848-1 |
| Net Weight | 20 lbs (9.1 kg) |
| Dimensions (H×W×D) | 10.3 × 6.6 × 18.8 in |
| Warranty | 3 Years |
| Condition | Factory Reconditioned — Lincoln Electric certified |